| ID |
Date |
Author |
Category |
Subject |
Text |
 |
|
45
|
Thu May 16 10:18:14 2024 |
Mayr, Hannes | Runs | Beam back | Beam is back since 10:10, but DAQ is turned
off to change the setting there.
Measurements starting at 10:18 are only test |
|
|
44
|
Thu May 16 09:41:56 2024 |
Mayr, Hannes | Runs | No beam | No beam from 09:39 to 10:10 due to a setting
change. The change aims to increase the measurement
time to 10s. |
|
|
43
|
Thu May 16 08:58:39 2024 |
Mayr, Hannes | Runs | Fluctuations in particle rate | Particle rates are fluctuating and increasing
from a constant 5e8 to something around 1e9. |
|
|
42
|
Thu May 16 07:50:39 2024 |
Mayr, Hannes | Runs | Peaks with very high particle rate | Peaks in the particle diagram going to unusual
high 1.4e9 particles. |
|
|
41
|
Thu May 16 07:25:33 2024 |
Mayr, Hannes | Runs | Lassie Screenshot 07:23 | Start of regular screenshots of the Lassie
monitor every 1-2 hours. |
|
|
40
|
Thu May 16 04:37:27 2024 |
Boguslaw, Camille | Runs | No beam to ESR | We had no beam in ESR for about 3 minutes |
|
|
39
|
Thu May 16 00:37:41 2024 |
Boguslaw, Camille | Runs | Injection pattern changed | The injection pattern changed on Lassie monitor
(0:27 AM). (picture 1)
|
|
|
38
|
Wed May 15 23:04:32 2024 |
Xinliang | Analysis | Electron cooler data | The cooler curve measured during May 14 afternoon. |
|
|
36
|
Wed May 15 20:40:51 2024 |
Jeroen, Johan | Runs | Beam returned to ESR | 20:39:42 Runs restarted. |
|
|
35
|
Wed May 15 20:17:20 2024 |
Jeroen | Accelerator | Fewer spills from SIS18 then lost beam | Apparently fewer spills coming from SIS18,
see attached.
|
|
|
34
|
Wed May 15 19:45:44 2024 |
Helmut Weick | Accelerator | Cooler curves after beam shift | After the Beam position tuning but before
the scraper tuning two more cooler curves
were taken.
|
|
|
33
|
Wed May 15 19:20:32 2024 |
Helmut Weick | Accelerator | scraper setting | After the orbit correction on the target straight
section the scrapers work better.
One pair of scrapers works best:
|
|
|
32
|
Wed May 15 18:37:36 2024 |
Jeroen, Johan, Shahab | Runs | Beam returned to ESR | Beam returned at 18:30:55. Taking data with
new triggers. |
|
|
31
|
Wed May 15 17:47:34 2024 |
Jeroen, Johan, Shahab | General | New Trigger Setup | We changed the trigger setup, see attachment |
|
|
30
|
Wed May 15 17:45:09 2024 |
Jeroen, Johan | General | No beam to ESR | Beam lost from SIS18 at 17:41:41. |
|
|
29
|
Wed May 15 17:22:43 2024 |
Jeroen, Shahab, Johan | Runs | 98Mo run | Beam tuned at 4:50, data acquisition aligned
for 98Mo at 4:56. |
|
|
28
|
Wed May 15 16:55:10 2024 |
Jeroen, Johan | General | Tuning ESR scraper. Isomer resolved. | 4:50 Scraper tuned to produce Gaussian beam
profile for 98Mo. Isomer now clearly resolved.
|
|
|
27
|
Wed May 15 13:39:10 2024 |
Beatriz, Min | General | ESR setting | From 13:37 ESR will be changed again. Now
back to the primary beam, it will be attempted
to measure the orbit of the beam. |
|
|
26
|
Wed May 15 12:58:12 2024 |
Beatriz, Min, Shahab | Runs | optimizing the mass resolution | Yuri and Sergey still optimizing the mass
resolution.
|
|
|
25
|
Wed May 15 11:59:32 2024 |
Beatriz, Min | DAQ | File transfer to lustre looks to be stopped | File transfer to lustre looks to be stopped
at around 11:35AM |
|