| ID |
Date |
Author |
Category |
Subject |
|
54
|
Thu May 16 16:38:11 2024 |
Ide, Hubbard | Runs | No beam to ESR |
because of problems in HHT
no beam from 16:36 |
|
53
|
Thu May 16 16:10:03 2024 |
Ide, Hubbard | Runs | Lassie Screenshot |
Lassie Screenshot taken at 16:09 |
| Attachment 1: 2024-05-16_16-08-02-778_tcl1064.png.pdf
|
|
|
52
|
Thu May 16 15:24:30 2024 |
Ide, Hubbard | Accelerator | new Plunger setting |
plunger motors were set
to +/-390 mm for 245 MHz resonator
and +/-55 mm for 410 MHz resonator |
|
51
|
Thu May 16 14:52:45 2024 |
Shahab | DAQ | Zr recording |
Recording Zr starting from 14:45 again back to short cycle. |
|
50
|
Thu May 16 13:04:02 2024 |
Mayr, Hannes | Runs | DAQ stopped, change setting to 98Zr |
Beam tuning for 98Zr starting at 12:53, following data should be excluded from analysis. DAQ was stopped around 13:13. |
|
Draft
|
Thu May 16 12:48:58 2024 |
Sergey | Accelerator | Tune to 98Zr |
- stop longer measurements
- change quadrupole and sextupole magnets
- rescale SIS-TE-ESR |
|
48
|
Thu May 16 11:20:10 2024 |
Sergey | Accelerator | Screenshot of ESR pattern with 140 repetitions (each is 100 ms) |
Injection Beam Process: 100ms
Bunching Beam Process: 16ms
Intermediate Beam Process: 100 ms, which is repeated 140 times
Intermediate Beam Process: 16 ms |
| Attachment 1: 2024-05-16_11-19-01-545.png
|
|
|
47
|
Thu May 16 11:13:05 2024 |
Mayr, Hannes | Runs | Rates |
With the new timing, the rates now look like can be seen in the screenshot. |
| Attachment 1: 2024-05-16_11-10-57-933_tcl1064.png
|
|
|
46
|
Thu May 16 11:08:27 2024 |
Mayr, Hannes | Runs | DAQ running again |
"Real" measurement with good data starting from 11:07 until approximately 13:00.
Measurement time was changed to 10s with injections every 32s. |
|
45
|
Thu May 16 10:18:14 2024 |
Mayr, Hannes | Runs | Beam back, DAQ off |
Beam is back since 10:10, but DAQ is turned off to change the setting there.
Measurements starting at 10:18 are only test runs and should not be used for analysis. |
|
44
|
Thu May 16 09:41:56 2024 |
Mayr, Hannes | Runs | No beam |
No beam from 09:39 to 10:10 due to a setting change. The change aims to increase the measurement time to 10s. |
|
43
|
Thu May 16 08:58:39 2024 |
Mayr, Hannes | Runs | Fluctuations in particle rate |
Particle rates are fluctuating and increasing from a constant 5e8 to something around 1e9. |
| Attachment 1: 2024-05-16_08-58-00-964_tcl1064.png
|
|
|
42
|
Thu May 16 07:50:39 2024 |
Mayr, Hannes | Runs | Peaks with very high particle rate |
Peaks in the particle diagram going to unusual high 1.4e9 particles. |
| Attachment 1: 2024-05-16_07-49-53-757_tcl1064.png
|
|
|
41
|
Thu May 16 07:25:33 2024 |
Mayr, Hannes | Runs | Lassie Screenshot 07:23 |
Start of regular screenshots of the Lassie monitor every 1-2 hours. |
| Attachment 1: 2024-05-16_07-23-30-208_tcl1064.png
|
|
|
40
|
Thu May 16 04:37:27 2024 |
Boguslaw, Camille | Runs | No beam to ESR |
We had no beam in ESR for about 3 minutes |
| Attachment 1: 2024-05-16_04-38-44-446_tcl1064.png
|
|
|
39
|
Thu May 16 00:37:41 2024 |
Boguslaw, Camille | Runs | Injection pattern changed |
The injection pattern changed on Lassie monitor (0:27 AM). (picture 1)
It when back to the previous rate at 1:48 AM. (picture 2)
The same pattern change appeared from 3:01 AM to 3:07 AM. (picture 3) and from 3:24 AM to 3:39 AM. |
| Attachment 1: 2024-05-16_00-34-07-585_tcl1064.png
|
|
| Attachment 2: 2024-05-16_01-53-34-896_tcl1064.png
|
|
| Attachment 3: 2024-05-16_03-10-00-258_tcl1064.png
|
|
|
38
|
Wed May 15 23:04:32 2024 |
Xinliang | Analysis | Electron cooler data |
The cooler curve measured during May 14 afternoon. |
| Attachment 1: 20240515230302.png
|
|
| Attachment 2: data_2024_-_sergey.xlsx
|
| Attachment 3: iso.xlsx
|
|
36
|
Wed May 15 20:40:51 2024 |
Jeroen, Johan | Runs | Beam returned to ESR |
20:39:42 Runs restarted. |
| Attachment 1: 2024-05-15_20-40-22-391_tcl1064.png
|
|
| Attachment 2: 2024-05-15_22-01-28-310_tcl1064.png
|
|
|
35
|
Wed May 15 20:17:20 2024 |
Jeroen | Accelerator | Fewer spills from SIS18 then lost beam |
Apparently fewer spills coming from SIS18, see attached.
Beam was lost at 20:17:52. |
| Attachment 1: 2024-05-15_20-16-49-990_tcl1064.png
|
|
| Attachment 2: 2024-05-15_20-18-47-422_tcl1064.png
|
|
|
34
|
Wed May 15 19:45:44 2024 |
Helmut Weick | Accelerator | Cooler curves after beam shift |
After the Beam position tuning but before the scraper tuning two more cooler curves were taken.
The first with all scrapers open shows a similar shape to before with the same quadrupole setting.
Afterwards the ESR ebergy was shifted by -0.8 MeV/u to get the beam more on an outer orbit.
The curve then is shifted and has a bit less acceptance. |
| Attachment 1: curce_1.PNG
|
|
| Attachment 2: curce_2.PNG
|
|
| Attachment 3: isoc_curves_15052024.xlsx
|