ELOG E127

HOME ESR EXPERIMENTS LABS etc

E121 E127 E132 E125 E143 laser_cooling_2021 E142 Ê128 E146 E0052 E0018 E0028 E0038

proton-capture on 118Te, Page 15 of 29

Not logged in

Find | Login | Help

Full | Summary | Threaded

572 Entries

Goto page Previous 1, 2, 3 ... 14, 15, 16 ... 27, 28, 29 Next

ID	Date	Author	Category	Subject	Text
55	Sun Mar 15 19:46:34 2020	Laszlo	Calibration	run042 - Xray35 calib Ba133 - high rate	Detector: 35 Source: Ba133, strong source Distance: 334mm
56	Sun Mar 15 20:26:08 2020	Laszlo	Calibration	run043 - Xray35 calib Am241	Detector: 35 Source: Am241 Distance: 334mm
58	Sun Mar 15 21:01:23 2020	Laszlo	Calibration	run044 - Xray35 calib Ba133 - a night long run	Detector: 35 Source: Ba133 Distance: 334mm
63	Thu Mar 19 09:43:28 2020	Laszlo	General	Status of the ESR	After two days of tuning the beam, yesterday evening (~8pm), it was found out that within one ESR pattern using the new control system
65	Thu Mar 19 19:14:40 2020	Laszlo	General	primary beam measurement	Now our aim is to decelerate the primary beam (naked 124Xe) down to 10MeV/u. At this energy we can test our detectors and that how the
66	Thu Mar 19 23:48:56 2020	Laszlo	General	124Xe primary beam at 10Mev TargetOFF	Beam lifetime is estimated to be 11sec at least (hard to.see with the cursor the corrct values on the shottky monitor)
67	Fri Mar 20 01:11:58 2020	Laszlo	General	Target - beam jntersection	We have managed to find the target position with the beam by looking at the xray spectra. The trick was that at 10mev we
68	Fri Mar 20 01:21:00 2020	Laszlo	General	target is switched on event based
70	Fri Mar 20 01:36:48 2020	Laszlo	General	124Xe primary beam at 10Mev TargetON	We didmt see any effect on the lifetime if the target is switched on. It is because we use only hydrogen target (but why
84	Fri Mar 20 16:48:00 2020	Laszlo	General	flipped Si shaper output in x and y	Yesterday evening we have found out that the energy signals from the silicon are negative --> wrong polarity of the shapers was chosen
89	Fri Mar 20 22:51:36 2020	Laszlo	General	Target on signal change	From the previous settings: JetOn mashine number 11
90	Fri Mar 20 22:54:30 2020	Laszlo	General	First view of the beam	Intensity from Sis 1.7E9 The intensity is too.low at ESR to be visible. However we could.catch it somehow with Shottky
91	Fri Mar 20 23:43:26 2020	Laszlo	General	Vacuum while moving in the detector at yesterday evening	Vacuum before DSSSD movement: 1.5844E-11 Top value after movement: 3.64378E-11
92	Sat Mar 21 01:25:07 2020	Laszlo	General	Vacuum while moving in the detector for fragment measurement	Stayed below E-10 Start:2.42E-11 Top after moving: 4.144E-11
93	Sat Mar 21 01:44:57 2020	Laszlo	General		from the SIS side they could optimize the intensity. we gained a factor ~3. Now the SIS intensity is at
97	Sat Mar 21 02:36:44 2020	Laszlo	General	detector and scraper position	For the 124Xe primary beam measurement: -with the DSSSD we scraped the beam at position -40
118	Sat Mar 21 11:25:47 2020	Laszlo		possible misalignement between target and fragment beam	after 9hours of measurement we see only 19 counts on our targetON silicon detector histo. this low count rate can indicate two scenarios:
119	Sat Mar 21 11:30:04 2020	Laszlo	General	MWPC movement	now we try to move the capture detector (MWPC in the 1. dipol before our Si setup) inside the ring while the DAQ was ON
123	Sat Mar 21 12:06:50 2020	Laszlo	General	run61 - SCRAPER moved out	we want to see any change on the Silicon count rate, because we will have now also Rutherford scattering.
125	Sat Mar 21 12:32:00 2020	Laszlo	General	Estimated target thickness	Target thickness must be like 5mm (was measured with a moving thin wire) The beam thickness is small because of the

Goto page Previous 1, 2, 3 ... 14, 15, 16 ... 27, 28, 29 Next

ELOG V3.1.5-fc6679b