| ID |
Date |
Author |
Category |
Subject |
Text |
 |
|
30
|
Wed Mar 23 16:16:42 2022 |
V. Hannen | Detectors | Control software for XUV and copper mirror detector | Attached you find a manual for the software
used to control the movement of the XUV detector
and the copper mirror detector.
|
|
|
42
|
Thu Mar 31 15:53:50 2022 |
Konstantin | Detectors | Control software for XUV and copper mirror detector | > Attached you find a manual for the software
used to control the movement of the XUV detector
and the copper mirror detector.
|
|
|
145
|
Fri Apr 8 00:06:37 2022 |
Patrick | Laser | Connection to the laser pc | To login to the laser pc use the command
xfreerdp -g 1920x1080 -u atplaser atppc023.campus.gsi.de |
|
|
228
|
Thu Apr 14 12:27:18 2022 |
Sebastian, Max | Detectors | Connection to XUV / Cu reestablished! | The connection to the XUV and Cu were lost
during the nightshift.
|
|
|
208
|
Mon Apr 11 11:05:35 2022 |
Sebastian, Kristian | Laser | Check laser power | we checked the UV laser power at 10:15 am.
It was only 8.5 - 9 mJ. Pumping power was
460 mJ, which is the maximum output of the |
|
|
16
|
Wed Mar 16 08:31:52 2022 |
Kristian | DAQ | Check cables and timing | Konstantin and I generated a signal in the
Messhütte and sent it to the ESR.
There, we used a 44m BNC cable that was sufficently |
|
|
213
|
Mon Apr 11 22:14:51 2022 |
Konstantin, Sarper | Laser | Changing of the wavelength range | It is planned to change the scan range of
the laser wavelength from 322.41 - 322.0
nm to 322.01 - 321.6 nm @ 4 a.m. |
|
|
25
|
Mon Mar 21 16:33:23 2022 |
| DAQ | Changing code of go4 | We agreed to indicate changes in the go4 analysis
code according to the
following scheme
|
|
|
26
|
Mon Mar 21 17:03:47 2022 |
| DAQ | Changing code of go4 | Correction: Comments in C/C++ start with //
, i.e. forward slash
|
|
|
184
|
Sat Apr 9 14:15:44 2022 |
Kristian, Max, Konstantin | DAQ | Change in LV code | We changed the LV code so that the Cobra Set
Wavelength is permanently sent. Before it
was only sent once at the beginning of each |
|
|
159
|
Fri Apr 8 11:02:04 2022 |
DW, YL, RSS, SL | | Change h=2 to h=1 | After changing to h=1
The frequency manipulation #5: f=242.021487MHz
(124th harmonic) [no bunching]
|
|
|
147
|
Fri Apr 8 01:48:57 2022 |
Patrick | DAQ | Bugged Trending plots? | The wavelengths/frequencies shown in the graph
in the labview window do not match the wavelengths/frequencies
in go4.
|
|
|
178
|
Sat Apr 9 04:40:01 2022 |
Patrick | DAQ | Bugged Trending plots? | The problem from yesterday (ID:147) still
persists. All the plots (not only the labview
stuff) comes in too late in go4. However, |
|
|
64
|
Sat Apr 2 10:22:21 2022 |
Rui-Jiu Chen, Ragan | General | Beam is in the ESR | Primary beam is in the ESR now. Markus and
the team are tuning the ESR. |
|
|
82
|
Sun Apr 3 18:41:11 2022 |
Konstantin and Rodolfo | Laser | Beam Position Stabilization | We (Konstantin and I) have optimized the TEM
"laser-beam position stabilization".
|
|
|
214
|
Mon Apr 11 22:33:16 2022 |
Carsten | General | Backup of data to the external RAID disks | |
|
|
199
|
Sun Apr 10 15:08:42 2022 |
Carsten | DAQ | Backup of Data from 1rst Scanrange to extrenal RAID1 HDDs | I just performed a backup of all data (+log-Files)
that were collected until now to the two
RAID HDDs.
|
|
|
89
|
Mon Apr 4 16:26:04 2022 |
Carsten | DAQ | Backup Harddisk /External Disk | Since we cannot write on lustre, as a temproal
solution two RAID 1 (mirror) USB hard disks
with cpacity 6 TB each are installed.
|
|
|
55
|
Fri Apr 1 16:46:33 2022 |
Carsten | Detectors | All pressuzied air drives are tested now and are working properly | All pressuzied air drives are tested now and
are working properly |
|
|
211
|
Mon Apr 11 18:46:31 2022 |
Rodolfo, Sarper and Konstantin | Laser | Alignment-check | We cross-checked the laser-ion alignment.
The horizontal position was optimized. However,
|
|