| ID |
Date |
Author |
Category |
Subject |
Year |
Text |
 |
|
388
|
Sat May 22 16:29:07 2021 |
Laszlo et al. | General | coolers are back | 2021 | we can measure again.
(please write a detailed description if needed) |
|
|
577
|
Wed Jul 14 14:46:05 2021 |
Jan, Sophia | Detectors | collimator geometry | 2021 | We have measured the collimator geometry.
The annotations of the variables can be found
in the attached sketch
|
10x |
|
149
|
Sat Mar 21 22:57:28 2020 |
Laszlo, Jan | DAQ | changing cables of the Xray 90 and 145 | | Energy signals of 90 and 145 degree detector
have been checked and exchanged
They were connected to the wrong ADC channel.
|
|
|
543
|
Sat May 29 13:43:39 2021 |
Tino, Rene, Yuri, Laszlo, Markus | Runs | change of settings | 2021 | from now on, everal beam setting will be different.
We could not get the beam back to were it
was before. When the scraper was pulled back |
|
|
293
|
Thu Apr 29 20:32:52 2021 |
Jan Glorius | Calibration | calibration sources | 2021 | We use the following list of sources for calibration
of the Xray detectors:
|
|
|
31
|
Thu Jan 23 16:35:47 2020 |
Laszlo | DAQ | cable documentation | | |
|
|
34
|
Fri Feb 21 09:39:40 2020 |
Laszlo | DAQ | cable documentation | | |
|
|
40
|
Wed Mar 11 14:33:44 2020 |
Laszlo | General | beam time manual | | Here you can find the digital version of the
E127 beam time manual. |
|
|
272
|
Mon Apr 6 23:00:51 2020 |
Laszlo | Calibration | beam energies for 124Xe and 118Te measurements | | "The e- cooler settings were the same for
the 124Xe and 118Te beams" - Sergey --> speed
of the ions is the same --> same MeV/u
|
|
|
576
|
Thu Jul 8 14:07:19 2021 |
Jan | Calibration | beam energies | 2021 | Table of ion energies calculated from cooler
parameters
|
|
|
357
|
Thu May 20 17:31:50 2021 |
Jan, Laszlo, Beatriz | General | beam & target alignement | 2021 | beam and target alignement was checked by
looking at the Xray rates. Best case when:
Target bump (position) SC 9: -18.5mm
|
|
|
21
|
Thu Aug 29 10:02:22 2019 |
Jan | Detectors | bakeout at ESR setup | | The bakeout for our detector setup has started
on the evening of 27.08.2019
We have a temperature sensor in the vacuum |
|
|
227
|
Mon Mar 23 07:56:51 2020 |
Laszlo | General | Yuri made magick and we operate again | | DSSSD was moved out (HV switched off)
also the scraper was mistakenly moved.
|
|
|
204
|
Sun Mar 22 19:49:12 2020 |
Michael, Laszlo, Yuri | | Yuri is still tuning FRS | | We filled the Xray detectors.
Yuri is sill tuning FRS for primary beam. |
|
|
469
|
Wed May 26 14:28:23 2021 |
Jan | Analysis | Xrays from 118Te & 124Xe | 2021 | Attached is a plot of the uncalibrated energy
spectra taken with the 90 degree xray detector
for 118Te (red) and 124Xe (blue).
|
|
|
86
|
Fri Mar 20 16:58:02 2020 |
Jan | DAQ | Xray2 & Xray3 cabling | | We found that Xray2 and Xray3 the cabling
is not consistent:
|
|
|
307
|
Tue May 4 14:34:51 2021 |
Jan Glorius | Detectors | Xray weight control induces signals | 2021 | When the readout/control of the det. weight
control via serial connection is active,
there is a clear signal induced in the Xray |
|
|
344
|
Sun May 16 11:54:12 2021 |
Jan Glorius | Calibration | Xray performance in lab | 2021 | These are the current Xray detector performances
in the lab using data from run0046
|
|
|
297
|
Fri Apr 30 10:55:34 2021 |
Jan Glorius | DAQ | Xray multi-triggers - blocking gate | 2021 | From the CFD of Xray1 (90deg) we get multiple
trigger signals every ~5sec for unknown reasons.
|
|
|
305
|
Mon May 3 14:55:44 2021 |
Jan Glorius | Calibration | Xray energy calib. table | 2021 | Here is the table of energy calibration lines
from Am241 for all Xray detectors for several
measurements.
|
|