| ID |
Date |
Author |
Category |
Subject |
|
32
|
Sat Mar 28 11:28:11 2020 |
Ragan, RuiJiu, Mei, Yuri, Tino | General | ESR open |
ESR is open now |
|
137
|
Fri Apr 3 13:39:58 2020 |
Ragan, Mei, Shahab, Laszlo | Runs | Eight hour measurement (S2: 0/35 mm) |
beam: 205Tl81+ (no scraping , Al ~1g/cm2)
energy: 400 MeV/u
storage time: 8 hr
S2: 0/35 mm
purpose: data with TARGET ON
Detector position (CsISiPHOS): out of the ring
Detector position (MWPC): -60 mm
run start at 11:17, run0303.lmd
file running: 0306.lmd
_______________________________________________________________________________
time when accumulation starts: 13:32
time when storage starts: 13:51
time when storage ends: 21:51
I_cooler during storage time: -1 mA
I_cooler = 179 mA
I_SIS: 2e9
ESR particles after stacking: 3e6 (offset 0)
Number of stackings: 50
Target ON density: 3.95e12
Target on time for measurement: 10 mins (by event mode)
time spend at manipulation 13 : 5 mins
(i.e. time for which electron cooler is on after gas jet)
at 18:30 (start was at 13:51) the stored particles: I_ESR = 1.7e6
at 19:00 the stored particles: I_ESR = 1.6e6
at 19:30 the stored particles: I_ESR = 1.48e6
at 20:00 the stored particles: I_ESR = 1.5e6
at 20:30 the stored particles: I_ESR = 1.4e6
at 21:00 the stored particles: I_ESR = 1.34e6
at 21:30 the stored particles: I_ESR = 1.34e6
NTCAp file:
SC_2020-04-03_11-20-14
\IQ_2020-04-03_11-20-05
IQ rate: 8 MS/s
(saved in drive : p)
copy and repeat the above (below the line) for every storage time measurement |
| Attachment 1: A9A3E9A0-85E9-4A47-93FA-5D722730FCFC.jpeg
|
|
| Attachment 2: B24C41F3-BD4D-4400-9A30-B9CEF7928BBE.jpeg
|
|
| Attachment 3: 7B276C07-1E38-4858-924E-DFEC12F10578.jpeg
|
|
|
130
|
Fri Apr 3 04:36:21 2020 |
Ragan, Pierre-Michel, Dima | General | Electron cooler problem which was then solved |
04:09 Electron cooler had some problem when we were stacking for 2 hours measurement.
04:20 GECEBG2T and GECEBG5T were Reset and then Switched on. Electron cooler started working again |
|
169
|
Mon Apr 6 20:03:50 2020 |
Ragan | General | Experiment finished )) |
E121 experiment is finished with the last 10 hours measurement at 19:47 ))
Many thanks to everyone for there significant contributions )) |
|
20
|
Fri Mar 27 13:04:17 2020 |
Ragan | General | FRS Settings until now |
Yuri and Helmut have been extensively involved in tuning and optimizing of the FRS.
26th March, 2020 (Evening setting):
1) 206Pb67+ beam from SIS @401.17 MeV/u.
2) SEETRAM in target area of FRS is used for stripping the beam from SIS to get 206Pb81+ and is then transported to ESR @400 MeV/u. (SEETRAM consists of three Ti foils of ~10 um thickness which are used for stripping purpose (more info: https://www-win.gsi.de/frs-setup/ ))
3) SL1 slits are opened +-10 mm to get rid of other charge states of 206Pb and only transport 206Pb81+ through FRS.
27th March, 2020 (Evening setting):
1) Different target (Be 1-6 g/cm2 with Nb backing) and degrader (Al)thicknesses are used for the optimization of 206Pb81+ with matter in FRS to get the beam with @400 MeV/u in ESR.
2) 206Pb67+ beam from SIS @540-560 MeV/u. |
| Attachment 1: frs.pdf
|
|
| Attachment 2: FRS.pdf
|
|
|
167
|
Mon Apr 6 14:17:54 2020 |
Yuri, Shahab | Runs | FRS valves |
We saw reduction in ESR beam life. It turned out that FRS has opened valves and venting caused us reduction of the quality of vacuum in ESR leading to beam loss. We manged to closed GEE5VV so that now beam is stable somehow.
how could you guys!!!!
arrrrgggggggg!!!!!!! |
| Attachment 1: 2020-04-06_14-22-20-965.png
|
|
|
151
|
Sat Apr 4 19:55:37 2020 |
Ragan, Alex, Esther | Runs | Failed measurement...Ten hour measurement (S2: 0/35 mm and S6: -20/7 mm) |
FAILED - measurement was stopped by sudden loss of the beam
beam: 205Tl81+ (no scraping , Al ~1g/cm2)
energy: 400 MeV/u
storage time: 10 hr
S2: 0/35 mm
s6: -20/7
purpose: data with TARGET ON
Detector position (CsISiPHOS): out of the ring
Detector position (MWPC): -60 mm
run start at 19:02, run0343.lmd
file running: 0347.lmd
_______________________________________________________________________________
time when accumulation starts: 19:17
time when storage starts: 19:55
time when storage ends: 05:55
I_cooler during storage time: -1 mA
I_cooler = 177 mA
I_SIS: 1.8e9
ESR particles after stacking: 2.5e6 (offset 3e5)
Number of stackings: 100
Target ON density: xxe12
Target on time for measurement: 10 mins (by event mode)
time spend at manipulation 13 : 5 mins
(i.e. time for which electron cooler is on after gas jet)
I_ESR (20:30) : 2.25e6
I_ESR (21:00) : 2.1e6
I_ESR (21:30) : 2.0e6
I_ESR (22:00) : 1.8e6
NTCAp file:
SC_2020-04-04_19-04-52
\IQ_2020-04-04_19-04-52
IQ rate: 8 MS/s
(saved in drive : O)
copy and repeat the above (below the line) for every storage time measurement |
| Attachment 1: 2020-04-04_19-54-47-760.png
|
|
| Attachment 2: 2020-04-04_20-02-26-363.png
|
|
|
63
|
Mon Mar 30 00:32:32 2020 |
Ragan | Runs | First measurement with 206Pb81+ beam |
beam: 206Pb81+
energy: 400 MeV/u
purpose: data with primary beam for detector efficiency and cross-section calculations
Detector position (CsISiPHOS): 60 mm
Detector position (MWPC): -10 mm
run start at 00:28 , run file: run0252.lmd
run stop at xx:xx , close file: run0.lmd
_______________________________________________________________________________
time: 00:28
I_cooler = 176 mA
SIS particles before: 3E8
ESR particles when gas jet is on: 2.4E6
Target ON density: 4.45E12
Target on time : 5 minutes
NTCAp file:
SC_2020-03-30_00_28_45
IQ_2020-03-30_00_28_45
(saved in drive: p)
copy and repeat the above (below the line) every 30 minutes |
|
64
|
Mon Mar 30 01:01:53 2020 |
Ragan | Runs | First measurement with 206Pb81+ beam |
beam: 206Pb81+
energy: 400 MeV/u
purpose: data with primary beam for detector efficiency and cross-section calculations
Detector position (CsISiPHOS): 60 mm
Detector position (MWPC): -10 mm
run start at 00:28 , run file: run0252.lmd
file currently running: run0257.lmd
_______________________________________________________________________________
time: 01:00
I_cooler = 176 mA
SIS particles before: 3.3E8
ESR particles when gas jet is on: 2.4E6
Target ON density: 4.49E12
Target on time : 5 minutes
NTCAp file:
SC_2020-03-30_00_28_45 (run ongoing)
IQ_2020-03-30_00_28_45 (run ongoing)
(saved in drive: p)
copy and repeat the above (below the line) every 30 minutes |
|
66
|
Mon Mar 30 01:25:57 2020 |
Ragan | Runs | First measurement with 206Pb81+ beam |
01:17 Problem with SIS is solved
01:19 run start 0258.lmd
beam: 206Pb81+
energy: 400 MeV/u
purpose: data with primary beam for detector efficiency and cross-section calculations
Detector position (CsISiPHOS): 60 mm
Detector position (MWPC): -10 mm
run start at 01:19 , run file: run0258.lmd
file currently running:
_______________________________________________________________________________
time: 01:19
I_cooler = 176 mA
SIS particles before: 1.5E8
ESR particles when gas jet is on: 2.8E6
Target ON density: 4.49E12
Target on time : 5 minutes
NTCAp file:
SC_2020-03-30_01-18-31
IQ_2020-03-30_00_22-52
(saved in drive: p)
copy and repeat the above (below the line) every 30 minutes |
|
68
|
Mon Mar 30 02:00:46 2020 |
Ragan | Runs | First measurement with 206Pb81+ beam |
beam: 206Pb81+
energy: 400 MeV/u
purpose: data with primary beam for detector efficiency and cross-section calculations
Detector position (CsISiPHOS): 60 mm
Detector position (MWPC): -10 mm
run start at 01:19 , run file: run0258.lmd
run stop at 02:05: stop file: 0265.lmd
_______________________________________________________________________________
time: 02:05
I_cooler = 176 mA
SIS particles before: 3.3E8
ESR particles when gas jet is on: 4E6
Target ON density: 4.53E12
Target on time : 5 minutes
NTCAp file:
SC_2020-03-30_01-18-31
IQ_2020-03-30_00_22-52
(saved in drive: p)
copy and repeat the above (below the line) every 30 minutes |
|
67
|
Mon Mar 30 01:43:58 2020 |
Ragan | General | First measurement with 206Pb81+ beam pattern details |
The following shows the pattern for first measurement in ESR (gas jet is on for = 60*5 secs = 300 secs as it can be seen on step SC7 in pattern).
One injection cycle runs for ~ 6 mins. |
| Attachment 1: 90FC7D41-6C97-4760-B5A3-3CF60643A405.jpeg
|
|
| Attachment 2: BF20DBD8-1672-4817-8412-13B29CBF2E0A.jpeg
|
|
|
114
|
Thu Apr 2 02:38:32 2020 |
Ragan, Yuri, Sergey, Esther, Oliver | Runs | First measurement with zero storage time |
beam: 205Tl81+ (with no scraping)
energy: 400 MeV/u
storage time: zero
purpose: data with TARGET ON
Detector position (CsISiPHOS): out of the ring
Detector position (MWPC): mm
run start at 01:48 , first file: run0287.lmd
run stop at xx:xx , last file: run0xxx.lmd
_______________________________________________________________________________
time: 1:48
I_cooler = mA
ESR particles after stacking:
Number of stackings: 20
Target ON density: 4.3e12
Target on time: 01:54:34
Target off time: 02:04:34
Target on time for measurement: 10 mins (by local mode)
NTCAp file:
SC_2020-04-01_16-36-43/0000xxx.iq.tdms
\IQ_2020-04-01_16-36-43/0000xxx.iq.tdms
IQ rate: 8 MS/s
(saved in drive : o)
copy and repeat the above (below the line) for every storage time measurement |
|
59
|
Sun Mar 29 21:34:46 2020 |
Ragan | Runs | First run |
beam: 206Pb81+
energy: 400 MeV/u
purpose: data with primary beam for detector efficiency and cross-section calculations
Detector position (CsISiPHOS): 60 mm
Detector position (MWPC): -10 mm
run start at 21:25 , run file: run0250.lmd
run stop at 21:31 , close file: run0250.lmd
_______________________________________________________________________________
time: 21:25
I_cooler = 177 mA
SIS particles before: 2E8
ESR particles when gas jet is on: 3.6E6
Target ON density: 4.34E12
NTCAp file:
SC_2020-03-29_21-27-57
IQ_2020-03-29_21-27-57
copy and repeat the above (below the line) every 30 minutes |
|
145
|
Sat Apr 4 10:32:16 2020 |
Ragan, Shahab | Runs | Five hour measurement (S2: 0/35 mm and S6: -20/7 mm) |
beam: 205Tl81+ (no scraping , Al ~1g/cm2)
energy: 400 MeV/u
storage time: 5 hr
S2: 0/35 mm
s6: -20/7
purpose: data with TARGET ON
Detector position (CsISiPHOS): out of the ring
Detector position (MWPC): -60 mm
run start at 22:11, run0308.lmd
file running: 0313.lmd
_______________________________________________________________________________
time when accumulation starts: 09:47
time when storage starts: 10:19
time when storage ends: 15:19
I_cooler during storage time: -1 mA
I_cooler = 177 mA
I_SIS: 1.75e9
ESR particles after stacking: 2e6 (offset 5e5)
Number of stackings: ~70 (was set to 80 but we missed few shots)
Target ON density: 3.91e12
Target on time for measurement: 10 mins (by event mode)
time spend at manipulation 13 : 5 mins
(i.e. time for which electron cooler is on after gas jet)
I_ESR (10:30) : 1.95e6
I_ESR (11:00) : -
I_ESR (11:37) : 1.7e6
I_ESR (12:00) : -
I_ESR (12:30) : -
I_ESR (13:00) : -
I_ESR (13:37) : 1.37e6
I_ESR (14:07) : 1.28e6
I_ESR (14:30) : -
I_ESR (15:00) : 1.20e6
NTCAp file:
SC_2020-04-03_22-12-50
\IQ_2020-04-03_22-13-48
IQ rate: 8 MS/s
(saved in drive : O)
copy and repeat the above (below the line) for every storage time measurement |
| Attachment 1: 2020-04-04_10-46-44-779.png
|
|
| Attachment 2: 245A948B-69B3-47C0-9F15-0EB6E27FACF0.jpeg
|
|
| Attachment 3: C49C19FE-7274-46AB-87BA-6C10292DC620.jpeg
|
|
|
158
|
Sun Apr 5 15:28:35 2020 |
Ragan, Alex, Esther | Runs | Four hour measurement (S2: 0/35 mm and S6: -20/7 mm) |
beam: 205Tl81+ (no scraping , Al ~1g/cm2)
energy: 400 MeV/u
storage time: 4 hr
S2: 0/35 mm
s6: -20/7
purpose: data with TARGET ON
Detector position (CsISiPHOS): out of the ring
Detector position (MWPC): -60 mm
run start at 19:02, run0343.lmd
file running: 0539.lmd
_______________________________________________________________________________
time when accumulation starts: 15:27
time when storage starts: 16:05
time when storage ends: 20:05
I_cooler during storage time: -1 mA
I_cooler = -1 mA (20 mA)
I_SIS: 2e9
ESR particles after stacking: 2e6 (offset 5e5)
Number of stackings: 100
Target ON density: 3.92e12
Target on time for measurement: 10 mins (by event mode)
time spend at manipulation 13 : 5 mins
(i.e. time for which electron cooler is on after gas jet)
I_ESR (16:30) : 1.9e6
I_ESR (17:00) : 1.75e6
I_ESR (17:30) : 1.6e6
I_ESR (18:00) : 1.55e6
I_ESR (18:30) : 1.45e6
I_ESR (19:00) : 1.3e6
I_ESR (19:30) : 1.25e6
I_ESR (20:00) : 1.2e6
NTCAp file:
SC_2020-04-04_19-04-52
\IQ_2020-04-04_19-04-52
IQ rate: 8 MS/s
(saved in drive : O)
copy and repeat the above (below the line) for every storage time measurement/ |
| Attachment 1: 2020-04-05_15-27-32-971.png
|
|
| Attachment 2: A2DFA8C1-D623-42FA-BBD5-1F75F51D51DD.jpeg
|
|
| Attachment 3: 2020-04-05_16-23-38-007.png
|
|
| Attachment 4: B17A216F-15D8-48F2-9403-37C8236A38C0.jpeg
|
|
| Attachment 5: 87D9890E-AC6D-4E3F-B45B-FED6A301253B.jpeg
|
|
| Attachment 6: 2020-04-05_20-16-54-054.png
|
|
| Attachment 7: 43239EE6-100B-4540-894C-B98E659BE472.jpeg
|
|
|
134
|
Fri Apr 3 11:59:50 2020 |
Ragan, Pierre-Michel, Dima | Runs | Four hour measurement (S2: 0/35 mm) |
beam: 205Tl81+ (no scraping , Al ~1g/cm2)
energy: 400 MeV/u
storage time: 4 hr
S2: 0/35 mm
purpose: data with TARGET ON
Detector position (CsISiPHOS): out of the ring
Detector position (MWPC): -60 mm
run start at 04:13, run0300.lmd
file running: 0301.lmd
_______________________________________________________________________________
time when accumulation starts: 06:50
time when storage starts: 07:01
time when storage ends: 11:01
I_cooler during storage time: -1 mA
I_cooler = 179 mA
I_SIS: 1.75e9
ESR particles after stacking: 2.3e6 (offset 1e5)
Number of stackings: 30
Target ON density: 3.3e12
Target on time for measurement: 10 mins (by event mode)
time spend at manipulation 13 : 5 mins
(i.e. time for which electron cooler is on after gas jet)
NTCAp file:
SC_2020-04-03_04-17-44
\IQ_2020-04-03_04-17-51
IQ rate: 8 MS/s
(saved in drive : p)
copy and repeat the above (below the line) for every storage time measurement |
| Attachment 1: 708F0673-2D65-4EFA-902F-7067FA5885B4.jpeg
|
|
| Attachment 2: 8D6B87F7-B622-41B6-8CBC-E6404443987F.jpeg
|
|
| Attachment 3: 2D175AD1-813B-4C6B-93E0-43B90EFE2584.jpeg
|
|
|
56
|
Sun Mar 29 18:55:19 2020 |
Shahab | Runs | Frequency list for identification |
Here are some frequencies for identification of the fragments.
Center freq: 243.352675
span: 2 MHz
from left to right:
242.480175
242.645175
242.807675
242.855175
242.972675
243.247675
243.260175
243.300175
243.330175
243.342675
243.352675 --> largest peak possibly 205-Tl-81+ (not 100% sure)
243.415175
243.450175
243.555175
243.627675
243.752675
243.790175
243.807675
243.955175
244.117675
244.282675 |
| Attachment 1: freqs.jpg
|
|
|
5
|
Fri Dec 7 11:39:41 2018 |
Jan Glorius | SlowControl | GUI for remote control of MSCF+MHV4 |
We have a GUI for remote controlling our MesyTec modules MSCF16 and MHV4 for E121 experiment.
Here is the instructions to run it:
1. login to GSI-linux using <litv-exp> user
2. get the EPICS environment by typing in terminal: epicsfind
3. type in terminal: GUIe121 (alias for 'medm -x /u/litv-exp/E121/medm/e121.adl')
if you get the message: 'medm: command not found' you didn't load the EPICS environment (2.)
The GUI is more or less self-explaining.
Be sure to follow this procedure when changing a value (e.g. threshold for MSCF):
1. click on small text-panel with value
2. leave mouse pointer inside panel
3. change value by typing
4. press enter |
|
8
|
Tue May 7 15:52:47 2019 |
Chen, Sidhu | SlowControl | GUI for remote control of MSCF+MHV4 [detailed] |
We have a GUI for remote controlling our MesyTec modules MSCF16 and MHV4 for E121 experiment.
Here is the instructions to run it:
1. login to GSI-linux using <litv-exp> user
litv-exp@astrum1:~$ ssh -X litv-exp@lxg1254.gsi.de
2. get the EPICS environment by typing in terminal: epicsfind
litv-exp@lxg1254:~$ epicsfind
Found nice EPICS in /u/litv-exp/epics/opt_x86_64-linux-gnu_4.9.2.
3. type in terminal: GUIe121 (alias for 'medm -x /u/litv-exp/E121/medm/e121.adl')
litv-exp@lxg1254:~$ GUIe121
if you get the message: 'medm: command not found' you didn't load the EPICS environment (1.)
The GUI is more or less self-explaining.
Be sure to follow this procedure when changing a value (e.g. threshold for MSCF):
1. click on small text-panel with value
2. leave mouse pointer inside panel
3. change value by typing
4. press enter |